9 mistakes when choosing a juicer

Getting fresh from almost any fruit and vegetable is now possible thanks to juicers. The technique is undoubtedly very convenient and functional, but only if you carefully approached the purchase. When choosing, you need to take into account a lot of criteria – to make it easier for you, we will consider the most common mistakes when buying a juicer.

Buy narrow neck auger juicer
Models with augers are great for getting juice from apples or pears – the cake at the exit is dry, vitamins are preserved as much as possible, and the cold pressing mode is also quite quiet.

Electric juicer Kitfort KT-1104-2 black 11 499 *
Despite the fact that most manufacturers and users recommend cutting products into small slices, auger models that are powerful enough can easily handle whole apples, pears or other fairly hard fruits. For such models, only one limitation is relevant – the width of the neck.

If you are looking for a whole fruit juicer, be sure to check if the apple flows freely through the neck. On average, the width of the throat should be 70-75 millimeters.

Buy a centrifugal juicer for processing berries
Centrifugal juicers, despite their many advantages, are far from being the most versatile. It’s all about the design – the centrifuge grinds food using centrifugal force with a very high rotation speed of up to 10,000 rpm. The resulting cut goes to a special strainer, which sifts out large particles and gives out juice.

Electric juicer Polaris PEA 0934A silver 4 599 *
It is because of this processing method that most centrifugal models are not suitable for berries. Grapes, raspberries, currants or strawberries contain seeds that quickly clog the sieve and reduce efficiency. Screw juicers, in turn, can easily grind such bones.

Okta-Certified-Developer dumps
5V0-23.20 exam
500-710 questions
P_SECAUTH_21 pdf questions
500-052 pdf dumps
500-701 exam dumps
500-285 exam questions
C_SACP_2202 practice test
050-733 practice exam
1Z0-1038-21 baindumps

Buy a model with a short interval of operation of the device
This is true for those who prepare large volumes of juice, for example, for conservation. When working with any juicer, the engine heats up quickly enough – you have to take a short break. The time of continuous operation varies quite a lot depending on each specific model.

For centrifugal – this is 1-10 minutes. Everything is connected with a high load on the engine, which has to accelerate the centrifuge to high speeds. For example, for Philips HR1869, the manufacturer specifies that the motor should not run longer than 60 seconds, which means that you will have to turn the motor on and off each time to extract the juice.

Owners of screw models can count on 10-30 minutes of continuous operation. Advanced air-cooled juicers for sale – the developers say they can be used without interruption. These models are quite expensive, so they are relevant for large workpieces.

Buy a model without engine overheating protection
Fascinated by the process, many users simply forget that the juicer needs to be given a break. If you do not want to burn the unit, then be sure to look for models with the function of protecting the engine from overheating. Such a system will automatically turn off the device at a critical load level and overheating. This is especially true for centrifugal models, which have just a short time of continuous operation.Electric juicer Braun J 300 black 9 199 *
Pay attention only to the power of the juicer
The power of the juicer affects the performance of the device – the higher the parameter, the harder the fruits you can process. Partially affects the time of continuous operation, since low-power motors do not overheat so quickly.

However, chasing this indicator does not always make sense. For example, screw models, even at low power, are able to effectively squeeze juice from most hard fruits. Although the augers rotate at a low speed – only 80-100 revolutions per minute, they easily crush almost any fruit. The high power of centrifugal models is usually combined with high noise – from 75 to 90 dB, which is comparable to the noise of urban transport on the street.

Chasing high-revving models
This is a typical mistake of buyers of centrifugal juicers who, under the impression of a figure of 18,000 rpm, are more likely to run for a purchase. First of all, it is worth finding out which mode is optimal? For almost all fruits, 10,000–12,000 revolutions are enough – at these speeds, the cake is already pressed against the wall, and the juice flows down to the sieve. A short-term turbo mode up to 15,000 rpm is possible, although its activation does not fundamentally affect the quality or volume of the juice obtained.

There is no point in chasing models with 15-20 thousand revolutions – such juicers are usually much louder, and also have less continuous operation time, especially at maximum speeds. Heat from the engine is also transferred to the centrifuge, which is why the heated juice changes its taste.

Buy an additional citrus juicer if you already have an auger
Citrus juicers are designed to extract juice from lemons, tangerines, pomegranates, limes and grapefruits. However, the auger model will do just fine with all these fruits – you just need to peel the peel to get delicious juice. The efficiency of the technique will be at least as good as citrus models, which means that there is no point in buying a second juicer exclusively for this list of fruits.

The only caveat is that citrus fruits are quite large, so they will have to be cut into slices in order to load them into the throat of a screw juicer.

Buy a model without a drip-stop system
In many models, freshly squeezed juice flows through a special spout into a nearby glass or other container. This is very convenient because you do not need to get any containers from the internal structure. However, this approach has one drawback – the remaining juice slowly flows down to the spout and drips.

The drop-stop system helps prevent this. It can be implemented in different ways – a rising spout, a special cap-plug, and so on. In any case, this is a useful addition that will prevent juice residues from dripping onto the table.

Electric juicer Redmond RJ-914S silver

Buy a model whose parts cannot be washed in a dishwasher
The instructions for most juicers explicitly state that certain parts cannot be washed in hot water – it destroys elastic gaskets and can lead to deformation of some plastic components.

Despite this, some components of the juicer can be washed using a dishwasher. This information must be checked with the manufacturer before purchase. If you have a dishwasher at home, this item is required. The main thing is to set a gentle mode with temperatures not higher than 60 ° C and not use caustic compounds.